Your Location:  Home > Product Information > Waterproof LED Strips > 600pcs SMD LEDs/5m 3528 LED Light Strip

600pcs SMD LEDs/5m 3528 Waterproof LED Light Strip

This 600pcs waterproof LED Strip Light is to satisfy people`s demand for high-brightness white light,you can replace the indoor lighting also has a good decorative effect.

• Features:
• 1: Red/Green/Blue/Yellow/Pure White/Warm White available.
  2: 3pcs LEDs per unit; Can be cut by 3 LED(DC12V)and 6LED (24V)and connect again by our accessories.
  3: 3pcs/6pcs LEDs per unit; Can be cut by 3 LED(DC12V)or 6LED (24V)and connected again by our accessories
  4: With 3M adhesive tape back,easy for installation.
  5: Input Voltage DC12V or DC24V.
  6: Anti-oxidation, anti-UV radiation and won't change color after long time use.
  7: High flexibility ,high transparence, flame-proof and environmental friendly.
  8: Silicone material offers good heat or cold resistance and is not easily broken.
  9: With silicone transparent waterproof connector can easily connect and totally waterproof .
  10: Waterproof Material: Silicone hollow tube ,Silicone glue and Silicone transparent waterproof connector

• This Waterproof LED strip lights can be in Not Waterproof:


              Not Waterproof

• Parameter:

• Part Number	LED Q'ty	LED Type	CCT Range	Size(MM)	Λd(nm)/Tc(K)	Flux(±5%)	Max Power	Lifetime
  GL-FA-PW	600PCS	TOP SMD 3528 LED	Pure White	5000X10	5500-6500K	2874lm	48W	30,000h
  GL-FA-WW	600PCS		Warm White		3000-3500K	2781lm		30,000h
  GL-FA-R	600PCS		Red		620-625nm	802.4lm		50,000h
  GL-FA-G	600PCS		Green		520-525nm	2402lm		50,000h
  GL-FA-B	600PCS		Blue		465-470nm	658.8lm		50,000h
  GL-FA-Y	600PCS		Yellow		585-590nm	967.6lm		50,000h

  The data above is under the test condition of Ta =25 degree ,DC 12V ,RH 85%

• Dimension:
• 

• Connect Drawing:
• 

• Application :
• Architectural lighting for window ,archway ,canopy and corridor.
  Decorative lights for holiday ,event ,show,exhibition .
  DIY light for home use.
  Backlight or edge lighting for sign.



• Operation Guidance:
• 
• To cut and seal at one end, please follow the steps: A1 A2 A3 B1 B2
  To cut and install waterproof connector at one end, please follow the steps: A1 A2 A3 C1 C2 C3 C4 C5
  A1 : Cut the light strip at the mark ”scissors” .
  A2: Screw to open the glue cap.
  A3: Use the thrust (another side of glue cap ) to puncture the surface.
  B1: Inject the silicon gel into the end cap without holes .
  B2: Push the strip into the cap and let gel dry for 1 hour.
  C1: Put the connector wire through the end cap holes.
  C2: Solder the wire onto the PCB .
  C3: After solder the two wires, push the strip into the end cap with wires carefully.
  C4 : Inject the silicon glue at the end of strip and cap .
  C5: Make sure end cap and strip are connected well and let gel dry for 1 hour.
  
  
• Accessories:
• 


• Note:
• 1、Please make LED drivers compatible with waterproof LED strips before use LED strips;
  2、To use waterproof led strips 5M in serial, longer than 5M in parallel;
  3、Before use,first check the power supply used in compliance with of the power requirements;
  4、Each roll ask for independent power supply;not to use of multi-volume series use;