Your Location:  Home > Product Information > Waterproof LED Strips > High output waterproof LED strip light

High Output Waterproof LED Strip Light (3528 SMD LEDs)

This type strip is to satisfy people`s demand for high-brightness white light,you can replace the indoor lighting also has a good decorative effect.

• Features:
• 1: Power 3528 TOP SMD LED as lighting resources .
  
• 2: Available cool white(TC:5700-6500K) and warm white(TC:2900-3300K) .
  
• 3: Input Voltage DC 12V or 24V .
  
• 4: Can be cut by 3 LEDS (DC 12v) and 6LEDS (DC 24v ) and connected again by our accessories; With 3M adhesive tape back .
  
• 5: Can be chosen copper PCB or white PCB .
  6: .Anti-oxidation, anti-UV radiation and won't change color after long time use .
  7: High flexibility ,high transparence, flame-proof and environmental friendly .
  8: Silicone material offers good heat or cold resistance and is not easily broken .
  9: With silicone transparence waterproof connector can easily connect and totally waterproof .
  10: Waterproof Material: Silicone hollow tube ,Silicone glue .
  
  
• Parameter with 300pcs SMD LEDs/5m LED Strip :



• Part Number	LED Q'ty	Size(mm)	Flux(15%)	Light Output(15%)	Color	MAX Power
  GL-HFA-PW-300	300PCS	5000X8	3004.5lm	300x4000MCD	Pure White	48(W )
  GL-HFA-WW-300	300PCS	5000X8	2799.2lm	300x4000MCD	Warm White	48(W )




• Parameter with 390pcs SMD LEDs/5m LED Strip :



• Part Number	LED Q'ty	Size(mm)	Flux(15%)	Light Output(15%)	Color	MAX Power
  GL-HFA-PW-390	390PCS	5000X8	3905.9lm	390x4000MCD	Pure White	62.4(W )
  GL-HFA-WW-390	390PCS	5000X8	3639lm	390x4000MCD	Warm White	62.4W )




• Parameter with 600pcs SMD LEDs/5m LED Strip :



• Part Number	LED Q'ty	Size(mm)	Flux(15%)	Light Output(15%)	Color	MAX Power
  GL-HFA-PW-600	600PCS	5000X8	6009lm	600x4000MCD	Pure White	96(W )
  GL-HFA-WW-600	600PCS	5000X10	5598.5lm	600x4000MCD	Warm White	96(W )

• How to connect:
• 
• To cut and seal at one end, please follow the steps: A1 A2 A3 B1 B2
  To cut and install waterproof connector at one end, please follow the steps: A1 A2 A3 C1 C2 C3 C4 C5
  A1 : Cut the light strip at the mark ”scissors” or by every 3 LED's.
  A2: Screw to open the glue cap.
  A3: Use the thrust (another side of glue cap ) to puncture the surface .
  B1: Inject the silicon gel into the end cap without holes .
  B2: Push the strip into the cap and let gel dry for 1 hour.
  C1: Put the connector wire through the end cap holes.
  C2: Solder the wire onto the PCB .
  C3: After solder the two wires, push the strip into the end cap with wires carefully.
  C4 : Inject the silicon glue at the end of strip and cap .
  C5: Make sure end cap and strip are connected well and let gel dry for 1 hour.

• This Waterproof LED strip can be in Non-waterproof:


              Not Waterproof

• Note :
• 1、please make LED drivers compatible with waterproof high output led strips before use LED strips.
  2、To use waterproof high output led strips 5M in serial, longer than 5M in parallel.
  3、Before use,first check the power supply used in compliance with of the power requirements.
  4、Each roll ask for independent power supply;not to use of multi-volume series use.