led feadback  Feedback
      led video  Video of GL

Home > News > LED Panel Light Installation

  • LED Panel Light Installation


    led panel light

    label two-side glue on power
    1.play this power backward (figure 1)
    2.After the Power play backwards, post 3M glue above the power supply (figure 2)
    Note: 3m plastic with a strong viscosity, pls carefully paste
    led panel lihgt
    3.3M Glue paste on the power, squash with the hand, make 3M glue tight stick on the power supply (FIG. 3)
    4.rip off 3 M Gule surface tape (figure 6)
    5.Tear Tape (FIG. 5)
    led panel light
    The power pack on led panel light back
    1.Pls make the power labeled 3M glue side paste on the panel lamp (figure 6.7)
    Note:
    1.Pls put a soft mat on the floor before Installing the power supply , lest scratches or damaged panel
    2.The Power fixed position and direction are not limited
    3.In order to ensure products shine achieve the best effect, Please carefully take and put when place the panel lamp .

    2.Make the power output terminal link to the panel lamp input (FIG 8)
    led panel light1.Please note the power wiring of positive and negative when installation power wiring (positive with word)
    2.Connect into the panel lamp terminals power wire needs to tighten with the screw
    3.To avoid danger, pls cut off power supply before connecting wiring.4.Lock the screw, pls not use greatly forcibly, lest crush the led panel light

    3.Make the power input terminal received AC power supply (FIG 9)
    led panel lightWarning:
    1.Please note that power wires' negative source, when installation
    2.Handle properly insulation in joint local, prevent leakage and emerge risk
    3.Wiring must cut off power supply,prevent occur the danger

    Embedded installation of led panel light
    led panel light
    1.Make the panel light placed above the ceiling
    Note:
    1.Taken the ceiling and LED panel light turn 45 degrees, and put it above the ceiling , pls do not force squeezing or through the ceiling
    2.please placed panel lamp handled with care, ensure the products shine with the best effect
    3.Choose embedded installation LED panel lamp, first consideration that wether the panel light and the size of the ceiling corresponds
    2.Make rotating face of the panel lamp down (FIG.12.13)
    led panel light

    3.Make the panel light and the ceiling lanterns position adjustment aligned, that is to say, completed the installation process (FIG.14)
    led panel light
    4.You can open power and lighting, when the Panel lamp completed installation (figure 15)
    led panel light
    Important:
    1.Pls checking and ensuring all joints is right connected after completed the installation
    2.Check and ensure all positive and negative of the joints power is correct
    3.Check all lock screw parts whether fixed lock

    Suspension installation of led panel light
    1.Make the corner fixing parts installed above panel lamp (FIG.16.17)
    led panel light
    Note:
    1.Pls put a soft mat on the floor before Installing corner fixing parts , lest scratches or damaged panel
    2.please placed panel lamp handled with care, ensure the products shine with the best effect
    3.Lock the screw, pls not use greatly forcibly, lest crush the panel lamp

    2.Make the corner fixing parts installation the ceiling top (FIG.19.20.21)led light panel
    1.The first open four φ5mm holes on the ceiling
    2.Make the glue plug put into open good holes
    3.Screw through fixed cap, locked in plug hole
    led light panel
    4.Power input connected with AC power supply (FIG.22)
    5.LED Panel lamp installation completed effect —open power and lighting (FIG. 23)
    Important:
    A:Pls checking and ensuring all joints is right connected after completed the installation
    B:Check and ensure all positive and negative of the joints power is correct
    C:Check all lock screw parts whether fixed lock
    LED panel light's average life-span over100,000 hours (equivalent 10 years), and more 20 times than the common products, stable operation . Saving the maintenance cost of operation can completely made up for original investment. LED small fever, compare with the traditional of lamps and lanterns, the LED panel light's consumption of power only10%-20%, which makes them more environmentally friendly, and more correspond with user's lighting budget.
    GL is a integration R&D design and production in the LED Panel lamp field LED Panel light Chinese manufacturer, production and packaging large enterprises, the company's products can satisfy ever-changing the world market illume requirement. Provide product series include various can directly replace incandescent lamps and lanterns LED light, high brightness, various emitting light colors for optional, welcome your inquiries

    Many other LED Panel Light for available.
    Thickness 8mm LED Panel Light Installation Manual

Contact Us
General lighting Electronic Co.,Ltd.
Tel: +86-769-82253316
Fax: +86-769-82253301
Mail: info@gl-leds.com
Web site: www.gl-leds.com
Address: F Building,Julong Industrial Park,Tianxin Meitang Community,Huangjiang Town,Dongguan,China
Feedback
Please click "Feedback" to leave your message and we'll reply you as soon as possible.
Certificate
led certificate

LED Light LED Tube LED Bulb LED Spotlight LED Panel light LED Strip LED Light Bar Contact GL

General lighting Electronic CO.,LTD. Copyright © 2010 . All rights reserved.General Lighting Electronic Co., Ltd. All rights reserved. No part of this photo may be reproduced, in any form or by any means, without permission inwriting from General Lighting Electronic Co. Ltd.
Top